[Solution] How to Setup Wireless-n WiFi Repeater 192.168.10.1 ?

Setup Wireless-n WIFI Repeater 192.168.10.1

Still, facing problems on doing the setup wireless-n WIFI repeater 192.168.10.1?

Don’t worry. Now your wireless n WIFI repeater setup process you will find here. Nice to hear you.

If you like to stay connected with the Internet world, you can use WIFI Repeater, and you are very conscious with your work, then you should use this Because it will improve your internet experience (speed). 

Nowadays, it’s beneficial to extend the coverage of the WIFI network. That’s why everyone is now using Wireless-n WIFI Repeater. You can take this device anywhere in the corner of any wall and take advantage of the internet because it is small and will boost your network signal. 

And here, four ways for a quick installation guide:-

  1. Wireless N repeater setup via web GUI
  2. Repeater mode using ethernet cable
  3. Using AP mode
  4. Wireless N Range Extender via WPS

Let’s know Setup Wireless-n WIFI Repeater 192.168.10.1

Configure or setup wireless N repeater via web GUI

  1. Plug your device on the switchboard and turn on the switch after there will blink up a green light.
  2. Now connect the Repeater with your Laptop/PC or Cell phone through the ethernet cable.
  3. Check your WIFI (turn on) network section. You will see a “Wireless N or WIFI repeater” to connect it with a network.
  4. Open your web browser and enter 192.168.10.1 in the address bar, and hit enter button.
  5. Your login page will open, and your 192.168.10.1 WIFI repeater user name & password is the same as “admin.”
  6. Click on the Repeater in the wizard section. 
  7. Select your network and put details of SSID and your repeater password and click on apply.
  8. It will take around 50-60 seconds, and after this, check your WIFI list and connect with _EXT network.

Setup Repeater mode using ethernet cable

For this setup procedure, you must have a PC/Laptop with an active wireless card.

  1. Connect the repeater with connector and connect ethernet cable with Laptop/PC.
  2. Open your web browser and enter 192.168.10.1 in the address bar, and hit enter button.
  3. All steps are now the same as above mentioned.

Setup using AP mode 

  1. Connect ethernet cable with the router and also connect the cable with WIFI repeater.
  2. Open your web browser and enter 192.168.10.1 in the address bar, and hit enter button.
  3. Your login page will open, and your 192.168.10.1 WIFI repeater user name & password is the same as “admin.”
  4. Click on the AP in the wizard section.
  5. Wireless AP mode in enter your SSID name and channel section “auto” and set up your security password.
  6. It will take 50-60 sec and will set up completely.

Setup Wireless N Range Extender via WPS

For this setup, make sure to remember that your device extender and router have not had more distance according to me 5-10 feet is enough. 

  1. Plug your Extender into a power outlet near your primary router.
  2. Press the WPS button on your main router till then when the light is not blinking when light is blinking start after immediately push the range extender WPS button.
  3. Within 2 minutes, press the Extender WPS button for connecting with the router.
  4. After that May it takes time 10-20 seconds.
  5. When your router and Extender are connected successfully then the appear Extender LED is blinking solid.

Final thoughts on Configure Wireless-n WIFI Repeater:-

I have covered all processes for connecting Extender with the router, ethernet cable, and Ap mode. And also attached a video for more comfortable to understand for you. Still, facing problems on doing the setup wireless-n WIFI repeater then drop your comment below we will shortly respond.

Leave a Reply

Your email address will not be published. Required fields are marked *